基于综采面产尘分布与扩散分析的粉尘防治研究

在对W3709综采工作面产尘特点分析的基础上,将工作面产尘源分为落煤扬尘、落煤冲击产尘及割煤产尘3类。对采煤机顺风割煤与逆风割煤时粉尘运动规律进行了详细的分析,根据工作面产尘特点与粉尘运动规律,提出了包括煤层注水、采煤机割煤产尘治理与控制以及支架处粉尘治理一套完整的综合防尘系统。通过现场应用,工作面粉尘在原有设施降尘基础上降低86%以上,降尘效果良好,有效地解决了该工作面粉尘污染严重的难题。     

连续型空间故障树中因素重要度分布的定义与认知

为了解工作环境条件因素对系统故障概率的影响的特征,同时丰富连续型空间故障树(CSFT)的理论框架,提出因素重要度分布的概念。因素重要度分布从经典故障树的概率重要度发展而来,目的是研究系统所处环境因素变化导致系统可靠性变化的程度。给出元件和系统的因素重要度分布概念、公式及所需基础数据,并分析因素重要度分布的正负分布特点。使用该概念研究元件X1和系统T的因素t重要度分布和因素c重要度分布。结果表明:在不同环境中,对于因素t或c变化影响元件或系统的故障概率变化程度是不同的。因素重要度分布有效地表达了t和c对元件或系统的故障概率影响特征。     

环境烟草烟气粒径分布及其对光散射的影响

为了测量典型办公室内环境中环境烟草烟气悬浮颗粒物的数浓度和粒径分布变化,以及其对颗粒光散射的影响,在6.8 m×3.2mx2.8 m的试验间进行试验,采用测量范围为5～1 000 nm的DMS500扫描电迁移率粒径谱仪进行粒径测量.结果表明,不同卷烟样品的烟气粒径分布曲线近似,都可以用对数正态分布函数来描述.4种卷烟样品粒径分布及参数变化速率相似,在4 800 s内数中值粒径CMD平均值从105 nm增大至155 nm,几何标准差GSD平均值从1,58减小至1.45,CMD和GSD的变化趋势近似符合指数函数.利用基于Mueller光散射理论的程序计算烟颗粒对散射光的影响.粒径分布的变化显著改变了颗粒散射光强度,CMD最大使散射光强度增大7倍,GSD引起的强度变化较小.综合考虑烟气颗粒数浓度降低和粒径分布的变化,散射光强度最大增大3倍.     

河南省武陟县大田土壤重金属形态分布及潜在生态风险评价

为了解河南省武陟县大田土壤重金属Cr、Cd、Pb、As、Cu、Se、Ni和Co的形态分布和生态风险情况,在该区域采集了12个表层土壤(0～20cm)样品,采用修正的BCR连续提取法进行形态分析,探讨其生物有效性,并采用Hakanson指数法评价了重金属的潜在生态风险.结果表明,土壤中不同重金属的形态分布差异很大,其中,Cr、As、Ni和Co均主要以残渣态存在,分别占其总量的66.6％、61.4％、50.7％和41.8％;Cu和Se主要以可氧化态存在,分别占其总量的43.8％和67.8％;Pb主要以可还原态存在,占总量的61.1％;Cd主要以酸提取态存在,占总量的53.3％.生物有效性分析表明,Cd的可利用态K1为0.933,生物有效性是最大的,对土壤生态系统的潜在危害性较大,其次是Pb和Co;Cu和Se在土壤环境发生变化时,很容易再次释放到外界环境中;Cr、As和Ni不易被外界生物利用.潜在生态风险评价结果显示,以国家土壤环境质量标准二级标准为参比值时,Cr、Cd、Pb、As、Cu和Ni的单项潜在生态风险程度均为轻微,综合潜在生态风险处于轻微等级.     

西安市PM2.5污染的时空分布

为探索PM2.5的分布规律及其影响因素,对2013年西安市13个监测站点的全年ρ(PM2.5)数据进行了统计与整理.分析了ρ(PM2.5)的时空分布,采用聚类分析、小波变换研究了ρ(PM2.5)的区域分布特征与年际变化及突变特征,并对相关因素进行了探讨.结果表明,西安市ρ(PM2.5)在时间分布上具有冬高夏低的特点,而在空间分布上则以市人民体育场和草滩监测点所在区域为ρ(PM2.5)高值中心;ρ(PM2.5)在空间上可分为3大类,纺织城监测点单独为1类,经开区与草滩监测点为2类,另外10个监测点为3类,聚类效果的相关系数为0.7994,显示聚类效果较好;在ρ(PM2.5)年际变化中,除了6月和7月以外,其他月份ρ(PM2.5)均值为147.29 μg/m3,日照时间短和静风是导致ρ(PM2.5)发生突变的主要气象因素.     

采空区瓦斯涌出源位置对瓦斯分布影响的数值模拟

根据多孔介质渗流理论,利用Fluent软件,分别对采空区瓦斯在整个采空区均匀涌出、上邻近层及底板遗煤涌出2种情况下采空区瓦斯分布规律进行了数值模拟.结果表明:采空区瓦斯为上邻近层及底板遗煤处涌出时,沿走向方向,靠近上邻近层及底板处高体积分数瓦斯距离工作面较近;沿竖直方向,瓦斯体积分数分布呈钩状,靠近瓦斯涌出源处瓦斯体积分数最高;整个采空区均匀涌出时采空区瓦斯体积分数分布与上邻近层及底板遗煤涌出时有很大差别.因此,为了得到更符合实际情况的瓦斯分布规律,数值模拟时应按照现场实际的瓦斯涌出源位置建立模型.     

Lower Leg Injury Reference Values and Risk Curves from Survival Analysis for Male and Female Dummies: Meta-analysis of Postmortem Human Subject Tests

Objective: Derive lower leg injury risk functions using survival analysis and determine injury reference values (IRV) applicable to human mid-size male and small-size female anthropometries by conducting a meta-analysis of experimental data from different studies under axial impact loading to the foot–ankle–leg complex.

Methods: Specimen-specific dynamic peak force, age, total body mass, and injury data were obtained from tests conducted by applying the external load to the dorsal surface of the foot of postmortem human subject (PMHS) foot–ankle–leg preparations. Calcaneus and/or tibia injuries, alone or in combination and with/without involvement of adjacent articular complexes, were included in the injury group. Injury and noninjury tests were included. Maximum axial loads recorded by a load cell attached to the proximal end of the preparation were used. Data were analyzed by treating force as the primary variable. Age was considered as the covariate. Data were censored based on the number of tests conducted on each specimen and whether it remained intact or sustained injury; that is, right, left, and interval censoring. The best fits from different distributions were based on the Akaike information criterion; mean and plus and minus 95% confidence intervals were obtained; and normalized confidence interval sizes (quality indices) were determined at 5, 10, 25, and 50% risk levels. The normalization was based on the mean curve. Using human-equivalent age as 45 years, data were normalized and risk curves were developed for the 50th and 5th percentile human size of the dummies.

Results: Out of the available 114 tests (76 fracture and 38 no injury) from 5 groups of experiments, survival analysis was carried out using 3 groups consisting of 62 tests (35 fracture and 27 no injury). Peak forces associated with 4 specific risk levels at 25, 45, and 65 years of age are given along with probability curves (mean and plus and minus 95% confidence intervals) for PMHS and normalized data applicable to male and female dummies. Quality indices increased (less tightness-of-fit) with decreasing age and risk level for all age groups and these data are given for all chosen risk levels.

Conclusions: These PMHS-based probability distributions at different ages using information from different groups of researchers constituting the largest body of data can be used as human tolerances to lower leg injury from axial loading. Decreasing quality indices (increasing index value) at lower probabilities suggest the need for additional tests. The anthropometry-specific mid-size male and small-size female mean human risk curves along with plus and minus 95% confidence intervals from survival analysis and associated IRV data can be used as a first step in studies aimed at advancing occupant safety in automotive and other environments.     

北京城6区大气颗粒物质量浓度变化规律研究

为较好地了解当前北京城6区大气颗粒物PM2.5和PM10质量浓度的污染水平及变化规律,根据2013年3月11日至2014年2月28日城6区12个空气质量实时监测点连续、实时的监测结果,构建多点位、完整时间序列的颗粒物质量浓度数据资料.应用数理统计分析手段,对当前北京城6区大气颗粒物质量浓度的频数分布、相关性和逐时变化特征进行分析,并结合全年实际气象特征,对引起大气颗粒物质量浓度变化的因素进行了初步探讨.结果表明,2013年3月至2014年2月北京城6区大气颗粒物污染较为严重,且PM2.5和PM10质量浓度具有特别显著的线性相关关系,全年相关系数达0.9,10年间无显著变化;二者年均值达91.7 μg/m3和116.9 μg/m3,分别超标162％和67％;二者质量浓度比达78.4％,10年间同比增长约20％.颗粒物质量浓度逐时变化受季节变化影响明显,总体呈现夜间最高、白天最低的趋势,变化周期为7～9h.研究表明,影响颗粒物质量浓度变化的因素包括春季的大风和生物粒子、夏季的湿热和降雨、秋季和冬季的逆温现象和降雪等气象因素及规律性的人为源因素.     

天津市夏季PM10浓度及组成元素垂直分布特征

通过天津市气象局大气边界层观测站高255 m的气象铁塔,获得了10m、40m、120m和220 m 4个高度共80个PM10样品,分析了PM10的日均质量浓度及其元素的垂直分布特征.结果表明,4个高度处PM10质量浓度时序变化基本一致;PM10质量浓度及其组成元素总量随高度增加递减;10 m、40m和120m3个高度处的PM10质量浓度时间序列分布的相关性较好,组分分歧系数较小,而220 m处的PM10质量浓度时间序列分布与其他3个高度处的相关性较差,组分分歧系数较大.样品中元素质量浓度由高到低依次是Si、Al、Ca、Fe、Na、Mg、K、Zn、Ti、Cu、Mn、Pb、Cr、Ni、Co、V、As、Cd和Hg.其中,Si、Al、Na、K质量分数随高度变化不大;Ca、Fe、Mg质量分数随高度增加递减明显;Zn、Cu、Mn、Pb、Cr在10m、40m和120 m3个高度处质量分数接近,而在220m处明显降低;Ti元素在4个高度处的质量浓度接近,质量分数总体上随高度增加递增;Ni、Co、V、As、Cd、Hg质量分数随高度的变化不同,其中与燃煤有密切关系的Hg在120 m处质量分数明显高于其他高度处,而在220m处最低.Al、Fe、Na、K等元素相对富集因子小于或接近1,其质量浓度与PM10质量浓度时序分布的相关性较好,其中Al、Na相关系数随高度增加显著递减;Zn,Cu、Pb、Cr、As、Ni的相对富集因子显著大于1,其质量浓度与PM10质量浓度时序分布的相关性较差,相关系数随高度增加变化不大.     

Auto-adaptive Air Distribution and Structure Optimization of Ejector Burner for Biomass Alcohol Fuels

A plenty of studies on the utilization of biomass alcohol fuels have been conducted, but combustion efficiency and stability of this fuels still need to be improved. Based on biomass alcohol fuels (bio-methanol and bio-ethanol), this paper studied auto-adaptive air distribution characteristics and optimum structure parameters of an ejector burner by numerical simulation method. Also, an experiment was conducted to verify the numerical results. The results show that the mole air entrainment ratio (MAER) keeps almost constant when the ejector fuel nozzle exit locates at the segment between the ejector throat and the suction chamber entrance, but a bigger ratio α would lead to a higher MAER till the α is bigger than 8.5 for bio-methanol and 11.5 for bio-ethanol. The bio-ethanol fuel is more beneficial for air carrying role because of its big molecular weight. Operation pressure (P_w) has a little impact on MAER of the two fuels, but the rise of back pressure (P_b) would lead to rapid decrease of MAER for the two fuels. For the optimum structure burners, the MAER can be maintained at the value of theoretical complete combustion. Its changing rate is less than 2.3% for bio-methanol and 2.5% for bio-ethanol when the burner load changes from 30% to 120%, which is highly consistent with the experimental results. The optimum burner can distribute air supply automatically with the changing of burner load.